Hoppa till innehåll
Free shipping over 3000 kr excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The scratch is visible to the eye but not in the report: how to measure directly on the microscope imageWhy a two-point measurement of a bore often shows the wrong diameter, and how a three-point micrometer solves itThree seconds instead of half a minute: how core temperature checks become a routine that actually gets doneA Hundred Bearing Seats per Shift: Read the Deviation Directly Instead of Calculating the DiameterThe hole measures correctly at the mouth but is tapered further in: how to find the fault without cutting up the partOne Second Is Enough to Tell Whether the Core Temperature PassesThree contact points give a bore measurement that doesn’t depend on who is holding the instrumentWhen the measurement has to be taken from an image: how automatic magnification reading makes microscope measurement traceableThe vernier caliper that keeps reading correctly when the scale is covered in coolant and chipsThree measuring points give the right bore size when the operator’s hand would otherwise decide the resultVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The scratch is visible to the eye but not in the report: how to measure directly on the microscope imageWhy a two-point measurement of a bore often shows the wrong diameter, and how a three-point micrometer solves itThree seconds instead of half a minute: how core temperature checks become a routine that actually gets doneA Hundred Bearing Seats per Shift: Read the Deviation Directly Instead of Calculating the DiameterThe hole measures correctly at the mouth but is tapered further in: how to find the fault without cutting up the partOne Second Is Enough to Tell Whether the Core Temperature PassesThree contact points give a bore measurement that doesn’t depend on who is holding the instrumentWhen the measurement has to be taken from an image: how automatic magnification reading makes microscope measurement traceableThe vernier caliper that keeps reading correctly when the scale is covered in coolant and chipsThree measuring points give the right bore size when the operator’s hand would otherwise decide the result

Two rubber seals can look identical and still have different hardness – here’s how to check

Published 13 October 2026 at 02:06

A new delivery of O-rings arrives, the dimensions are correct and the color is right. Yet after a few weeks the seals start to leak, or they become so hard that they crack in the cold. The cause is often that the hardness of the rubber deviates from the specification. It cannot be seen with the naked eye and cannot be measured with a vernier caliper.

Digital Shore A hardness tester, measuring range 0-100 Shore, resolution 0.1 Shore, accuracy ±1 Shore, measuring length 2.5 mm, material thickness ≥6 mm, RS232C data output, on/off button, automatic shut-off, max function, averaging of up to 9 measurements, dimensions 161×65×28 mm, supplied with the manufacturer's test report in a plastic case, according to DIN ISO 48-4 and ISO 868

What a Shore A hardness tester measures

The instrument measures how much a soft material resists a spring-loaded pin being pressed into it. The result is given on the Shore A scale, 0 to 100. This digital model has a resolution of 0.1 Shore and an accuracy of ±1 Shore, and it complies with DIN ISO 48-4 and ISO 868. These are the standards that the rubber and plastics industries refer to in their specifications.

What problems it solves

Hardness is one of the few properties that both supplier and customer can check quickly and without destroying the part. With an analog tester, the reading is affected by who is looking and how quickly. Here the value is displayed digitally, and the max function holds the highest value. You can also calculate the average of up to nine measurements, which evens out variations in the material. Via the RS232C output, the values can be transferred to a computer or quality system, so they don’t have to be copied by hand.

When and how it is used

Press the instrument against the surface so that the base plate sits flush, and read the value. The measuring length is 2.5 mm and the material should be at least 6 mm thick. Thinner samples give misleading values because the substrate affects the result. The instrument measures 161×65×28 mm and is supplied in a plastic case with the manufacturer’s test report, so it is easy to take along to the machine.

Three use cases

Incoming inspection in the engineering industry. Seals, gaskets and dampers are checked against the specified Shore A hardness before they are fitted. Deviating batches are caught before they end up in an expensive hydraulic cylinder.

Food production. Rubber seals in pumps, valves and conveyor belts harden over time due to heat, cleaning agents and grease. Regular measurements show when a seal is approaching the end of its service life, so that it can be replaced during a planned stop rather than after a breakdown.

Maintenance in manufacturing with rubber parts. Rollers, hoses and vibration dampers can be compared against reference values. If the value changes over time, it may indicate that the material is aging or that the wrong compound has been used.

Why it pays off

An instrument in this class costs less than a single unplanned production stop. If you factor in scrap, complaints and emergency seal replacements, the benefit becomes clear. Discussions with the supplier also become easier when you have a documented measurement value to show.

If you want to have control over the hardness of your rubber instead of assuming it, the tester is available from us.

Read more

More news

All news