Hoppa till innehåll
Free shipping over 3000 kr excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The scratch is visible to the eye but not in the report: how to measure directly on the microscope imageWhy a two-point measurement of a bore often shows the wrong diameter, and how a three-point micrometer solves itThree seconds instead of half a minute: how core temperature checks become a routine that actually gets doneA Hundred Bearing Seats per Shift: Read the Deviation Directly Instead of Calculating the DiameterThe hole measures correctly at the mouth but is tapered further in: how to find the fault without cutting up the partOne Second Is Enough to Tell Whether the Core Temperature PassesThree contact points give a bore measurement that doesn’t depend on who is holding the instrumentWhen the measurement has to be taken from an image: how automatic magnification reading makes microscope measurement traceableThe vernier caliper that keeps reading correctly when the scale is covered in coolant and chipsThree measuring points give the right bore size when the operator’s hand would otherwise decide the resultVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The scratch is visible to the eye but not in the report: how to measure directly on the microscope imageWhy a two-point measurement of a bore often shows the wrong diameter, and how a three-point micrometer solves itThree seconds instead of half a minute: how core temperature checks become a routine that actually gets doneA Hundred Bearing Seats per Shift: Read the Deviation Directly Instead of Calculating the DiameterThe hole measures correctly at the mouth but is tapered further in: how to find the fault without cutting up the partOne Second Is Enough to Tell Whether the Core Temperature PassesThree contact points give a bore measurement that doesn’t depend on who is holding the instrumentWhen the measurement has to be taken from an image: how automatic magnification reading makes microscope measurement traceableThe vernier caliper that keeps reading correctly when the scale is covered in coolant and chipsThree measuring points give the right bore size when the operator’s hand would otherwise decide the result

A Hundred Bearing Seats per Shift: Read the Deviation Directly Instead of Calculating the Diameter

Published 14 November 2026 at 05:58

It is Tuesday afternoon and fifty gearbox housings are sitting on the pallet after machining. All of them have the same bearing seat and all of them need to be inspected. With an internal micrometer, each bore gives you an absolute diameter that has to be read, noted down and compared against the tolerance. After twenty parts, both your patience and your concentration are gone. This is the situation where a bore gauge with a dial indicator proves its worth.

Mitutoyo mätinstrument med analog indikatorklocka för invändig hålmätning, 160-250 mm

What it is

Mitutoyo’s bore gauge for 160-250 mm is a comparative measuring instrument. You zero the dial indicator against a setting ring or a master block at the nominal diameter. Then you pass the bore gauge through each part and read the deviation from the nominal size directly on the dial. The dial indicator has a resolution of 0.001 mm, the measuring depth is 250 mm, and the instrument has an 8 mm clamping shank for mounting in a stand or fixture. The spring-loaded measuring contact presses against one bore wall and the fixed anvil against the opposite one, and the movement is transferred to the dial via a lever.

What problem it solves

Absolute measurement is slow when the question is really a simple one: is the bore within tolerance or not? A bore gauge answers that with a glance at the pointer. You can also see which way the dimension is drifting. This is valuable on a machine where tool wear slowly shifts the diameter, because the trend becomes visible before any part ends up outside the tolerance.

The technique takes a little skill. To find the true diameter, you rock the bore gauge slightly in the bore and take the minimum reading, which corresponds to the chord through the center. An experienced inspector does this without thinking, but it should be included in the instructions for new operators.

How it is used in practice

Machine shops: bearing seats in gearbox housings, engine blocks and pump housings are typical examples. After each machining cycle, the operator checks the bore at the machine and corrects the tool offset when the pointer approaches the tolerance limit.

Quality control: for sampling or final inspection of a series of identical parts, it is quick to sort out the few that deviate. The measured values can be documented as deviations from nominal, which is easy to compile.

Maintenance and repair: hydraulic cylinders and large bearing housings can be measured for wear and out-of-roundness. By measuring in several directions, you can see whether the bore has become oval, which a single diameter value can conceal.

Why it pays off

Time per part is the clearest gain. When hundreds of bores with the same nominal size need to be inspected, there is less reading and less calculating, and therefore fewer sources of error. The second gain is that deviations are detected early. A housing that is scrapped after all machining steps are completed is expensive, and it is cheaper to adjust the machine while the dimension is still within tolerance. Also keep in mind that the setting ring and the part should be at the same temperature, otherwise you are measuring thermal expansion instead of form. Verify the zero at regular intervals during the shift.

For anyone measuring large bores in series, a bore gauge in this size range is one of the most practical tools on the bench.

Read more

More news

All news