Hoppa till innehåll
Free shipping over 3000 kr excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The scratch is visible to the eye but not in the report: how to measure directly on the microscope imageWhy a two-point measurement of a bore often shows the wrong diameter, and how a three-point micrometer solves itThree seconds instead of half a minute: how core temperature checks become a routine that actually gets doneA Hundred Bearing Seats per Shift: Read the Deviation Directly Instead of Calculating the DiameterThe hole measures correctly at the mouth but is tapered further in: how to find the fault without cutting up the partOne Second Is Enough to Tell Whether the Core Temperature PassesThree contact points give a bore measurement that doesn’t depend on who is holding the instrumentWhen the measurement has to be taken from an image: how automatic magnification reading makes microscope measurement traceableThe vernier caliper that keeps reading correctly when the scale is covered in coolant and chipsThree measuring points give the right bore size when the operator’s hand would otherwise decide the resultVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The scratch is visible to the eye but not in the report: how to measure directly on the microscope imageWhy a two-point measurement of a bore often shows the wrong diameter, and how a three-point micrometer solves itThree seconds instead of half a minute: how core temperature checks become a routine that actually gets doneA Hundred Bearing Seats per Shift: Read the Deviation Directly Instead of Calculating the DiameterThe hole measures correctly at the mouth but is tapered further in: how to find the fault without cutting up the partOne Second Is Enough to Tell Whether the Core Temperature PassesThree contact points give a bore measurement that doesn’t depend on who is holding the instrumentWhen the measurement has to be taken from an image: how automatic magnification reading makes microscope measurement traceableThe vernier caliper that keeps reading correctly when the scale is covered in coolant and chipsThree measuring points give the right bore size when the operator’s hand would otherwise decide the result

Three contact points give a bore measurement that doesn’t depend on who is holding the instrument

Published 11 November 2026 at 16:53

Two people measure the same bore with the same instrument and get different answers. One tilts the measuring head slightly, the other doesn’t quite find the largest diameter. The difference is only a few micrometers, but it can be enough for a fit to be rejected, or approved for the wrong reason. In internal measurement, the operator is often the biggest source of uncertainty.

Digital internal three-point micrometer, Holtest type, IP65, Ø20–25 mm

What the instrument is

This is a digital internal three-point micrometer of the Holtest type for bores in the Ø20–25 mm range. Three carbide measuring surfaces are positioned at 120° intervals around the axis. When the measuring head is inserted into the bore and expanded, it centers itself, so the diameter is read off without you having to find the right position by hand. The resolution is 0.001 mm and the accuracy is stated as ±0.004 mm. The entire range is covered without having to change measuring pins.

Which problems it solves

Two-point instruments require you to both center the instrument and hold the correct angle, and that is where errors arise. With three contact points, much of that feel is removed from the equation. You zero against a setting ring of nominal diameter, insert the head and read the value. The choice between ABS and INC, switching between mm and inch, and the use of reset and preset make the instrument work both at the bench and at the machine. The IP65 rating handles coolant and dust, and the automatic shut-off saves the battery (V357 or CR2032).

Three use cases

In the manufacturing industry, it is used to check drilled and reamed bores in housings and fixtures. It is quick to measure at several depths and thereby detect taper before a part leaves the machine. In hydraulics maintenance, cylinder bores and guide bushings are checked for wear, where ovality or slight taper explains why a seal leaks. In compressor and engine workshops, cylinders are measured during overhaul, where the result determines whether honing is sufficient or whether more extensive work is required.

Why it pays off

The cost of a faulty measurement is seldom the measurement itself. It is the scrap, the rework or the complaint that follows. An instrument that gives the same value regardless of who measures reduces the number of re-measurements and discussions between shifts and between supplier and customer. Digital reading eliminates interpretation errors on the scale, and carbide surfaces wear slowly, which keeps calibration intervals stable. The instrument is delivered in an aluminum case that protects the measuring head in a workshop environment.

Keep in mind that three-point measurement is only as good as the setting ring. Use a ring with a traceable diameter, zero at a temperature close to room temperature, and verify the ring according to your regular intervals.

If you measure bores in the 20–25 mm range several times a day and want to eliminate operator dependency, this is an instrument worth a closer look.

Read more

More news

All news