Hoppa till innehåll
Free shipping over 3000 kr excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The scratch is visible to the eye but not in the report: how to measure directly on the microscope imageWhy a two-point measurement of a bore often shows the wrong diameter, and how a three-point micrometer solves itThree seconds instead of half a minute: how core temperature checks become a routine that actually gets doneA Hundred Bearing Seats per Shift: Read the Deviation Directly Instead of Calculating the DiameterThe hole measures correctly at the mouth but is tapered further in: how to find the fault without cutting up the partOne Second Is Enough to Tell Whether the Core Temperature PassesThree contact points give a bore measurement that doesn’t depend on who is holding the instrumentWhen the measurement has to be taken from an image: how automatic magnification reading makes microscope measurement traceableThe vernier caliper that keeps reading correctly when the scale is covered in coolant and chipsThree measuring points give the right bore size when the operator’s hand would otherwise decide the resultVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The scratch is visible to the eye but not in the report: how to measure directly on the microscope imageWhy a two-point measurement of a bore often shows the wrong diameter, and how a three-point micrometer solves itThree seconds instead of half a minute: how core temperature checks become a routine that actually gets doneA Hundred Bearing Seats per Shift: Read the Deviation Directly Instead of Calculating the DiameterThe hole measures correctly at the mouth but is tapered further in: how to find the fault without cutting up the partOne Second Is Enough to Tell Whether the Core Temperature PassesThree contact points give a bore measurement that doesn’t depend on who is holding the instrumentWhen the measurement has to be taken from an image: how automatic magnification reading makes microscope measurement traceableThe vernier caliper that keeps reading correctly when the scale is covered in coolant and chipsThree measuring points give the right bore size when the operator’s hand would otherwise decide the result

The vernier caliper that keeps reading correctly when the scale is covered in coolant and chips

Published 15 October 2026 at 12:01

Anyone who has worked at a CNC machine recognizes the situation. The vernier caliper sits next to the machine, the scale is slick with coolant and full of fine chips, and the display shows a value that doesn’t match the previous one. The operator measures again, doubts the instrument and wipes it off. A few minutes are lost every time, and sometimes a part gets passed on a value that was never quite right.

Mitutoyo digitalt skjutmått med Digimatic-gränssnitt, mätområde 0-200 mm

What it is

The Mitutoyo Absolute Digimatic in the PREMIUM LINE version, model 64-500152, is a digital vernier caliper with a measuring range of 0-200 mm, a resolution of 0.01 mm and an accuracy of ±0.02 mm. What sets it apart from simpler models is the AOS sensor, an electromagnetic-inductive absolute measuring system. It is deliberately insensitive to coolant, oil and chips on the scale surface, where a capacitive sensor easily becomes unreliable. The caliper has 50 mm jaws, a thumb wheel and a flat depth rod, and is delivered in a plastic case with an inspection report.

What problems it solves

The absolute sensor means the zero point is retained when the battery (V357) is replaced. You don’t need to reset it and risk measuring incorrectly without noticing. The slider speed is unlimited, so you can sweep across the entire range without losing count. The ABS/INC switch means the same instrument works both for absolute measurement and for comparative measurement from your own zero point. Note that the protection class is IP40. The sensor principle tolerates dirt on the scale, but the instrument is not intended to be submerged or rinsed.

Use in practice

In the workshop industry it is used at the machine to check diameters, steps and groove widths between operations, even when the part comes straight out of the coolant flow. The thumb wheel and depth rod make it easy to measure pocket depths and seating heights with one hand.

In quality control the Digimatic output is the key feature. With a Digimatic cable, USB Input Tool or wireless U-WAVE module, readings can be sent directly to Excel or a quality system. This eliminates handwritten records and the transcription errors that come with them.

For incoming inspection and maintenance, spare parts, bearing seats and worn shaft journals are checked against the drawing. A resolution of 0.01 mm is more than adequate there, and the inspection report comes with the instrument as documentation for traceability.

Why it pays off

A vernier caliper costing around SEK 3,800 is not a large item in a workshop’s budget. The cost of doubtful measurements is greater: remeasuring, downtime while waiting for a reliable value, and scrapped parts that were actually acceptable. Every time an instrument becomes unreliable because of dirt or a battery change, operators lose confidence in it. A vernier caliper that behaves the same way every day saves time on every shift, and the data transfer removes an entire manual step from the documentation.

If you want to see specifications, accessories and availability, everything is on the product page.

Read more

More news

All news