Hoppa till innehåll
Free shipping over 3000 kr excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The scratch is visible to the eye but not in the report: how to measure directly on the microscope imageWhy a two-point measurement of a bore often shows the wrong diameter, and how a three-point micrometer solves itThree seconds instead of half a minute: how core temperature checks become a routine that actually gets doneA Hundred Bearing Seats per Shift: Read the Deviation Directly Instead of Calculating the DiameterThe hole measures correctly at the mouth but is tapered further in: how to find the fault without cutting up the partOne Second Is Enough to Tell Whether the Core Temperature PassesThree contact points give a bore measurement that doesn’t depend on who is holding the instrumentWhen the measurement has to be taken from an image: how automatic magnification reading makes microscope measurement traceableThe vernier caliper that keeps reading correctly when the scale is covered in coolant and chipsThree measuring points give the right bore size when the operator’s hand would otherwise decide the resultVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The scratch is visible to the eye but not in the report: how to measure directly on the microscope imageWhy a two-point measurement of a bore often shows the wrong diameter, and how a three-point micrometer solves itThree seconds instead of half a minute: how core temperature checks become a routine that actually gets doneA Hundred Bearing Seats per Shift: Read the Deviation Directly Instead of Calculating the DiameterThe hole measures correctly at the mouth but is tapered further in: how to find the fault without cutting up the partOne Second Is Enough to Tell Whether the Core Temperature PassesThree contact points give a bore measurement that doesn’t depend on who is holding the instrumentWhen the measurement has to be taken from an image: how automatic magnification reading makes microscope measurement traceableThe vernier caliper that keeps reading correctly when the scale is covered in coolant and chipsThree measuring points give the right bore size when the operator’s hand would otherwise decide the result

Why a standard micrometer gives wrong readings on soft materials, and how to avoid it

Published 13 October 2026 at 18:34

Two inspectors measure the same gasket and get different values. One tightens the micrometer’s screw a little harder, the other stops at the friction thimble, and the material is compressed by different amounts. The difference is only a few hundredths of a millimetre, but it is enough for a seal to be approved in one place and rejected in another. The problem is well known in any operation that measures rubber, silicone or soft plastic.

Mitutoyo digital special micrometer, with non-rotating spindle and offset measuring faces for soft materials (IP65), 75-100 mm, resolution 0.001 mm

What kind of instrument it is

This is a digital special micrometer from Mitutoyo for the 75–100 mm measuring range, with a resolution of 0.001 mm. It has a non-rotating spindle and measuring faces designed for soft materials. The instrument is also rated IP65, so it withstands splashes and dust in a workshop or production environment. The display gives a direct reading without parallax error, and you can zero it anywhere in the range and switch between mm and inches.

What problems it solves

When a spindle rotates against a soft material, it pushes or twists the surface slightly sideways. With a spindle that only moves straight forward, this effect does not occur. The measuring faces are designed for materials that yield, so you can read the dimension without deforming the part more than necessary. The digital readout removes yet another source of error, namely the scale being interpreted differently by different people.

When and why it is used

Use it when the tolerance is tight and the material is sensitive to pressure. This applies particularly to larger dimensions, where a standard micrometer with a hard flat face easily gives a reading that is too low. Zero it against a reference, measure the same way every time and document the result. This makes the measurements comparable between shifts, departments and suppliers.

Three areas of use

Engineering and manufacturing: Bushings and washers made of PTFE, nylon and other engineering plastics change shape under load. When performing incoming inspection of such parts, the dimension needs to be reproducible, otherwise you end up in a discussion with the supplier.

Sanitary installations and piping systems: Sealing rings and rubber gaskets in larger dimensions must have the right thickness to seal without being crushed. Here the IP65 rating is practical when the measurement takes place close to the point of installation.

Food production: Silicone and rubber parts in process equipment wear and take a set over time. Regular thickness measurement shows when it is time to replace them, before a leaking gasket stops the line or leads to a deviation.

Why it pays off

The price is higher than for a standard micrometer, but the cost of incorrect measurements is usually greater. Parts rejected in error, approved parts that should have been stopped, and time spent on rechecks and complaints quickly cost more than the difference in purchase price. You also do not need several instruments or separate procedures to compensate for soft materials. One instrument and one method are enough.

If you measure soft materials in this range, it is worth reviewing the specification and comparing it with the method you use today.

Read more

More news

All news