Hoppa till innehåll
Free shipping over 3000 kr excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The scratch is visible to the eye but not in the report: how to measure directly on the microscope imageWhy a two-point measurement of a bore often shows the wrong diameter, and how a three-point micrometer solves itThree seconds instead of half a minute: how core temperature checks become a routine that actually gets doneA Hundred Bearing Seats per Shift: Read the Deviation Directly Instead of Calculating the DiameterThe hole measures correctly at the mouth but is tapered further in: how to find the fault without cutting up the partOne Second Is Enough to Tell Whether the Core Temperature PassesThree contact points give a bore measurement that doesn’t depend on who is holding the instrumentWhen the measurement has to be taken from an image: how automatic magnification reading makes microscope measurement traceableThe vernier caliper that keeps reading correctly when the scale is covered in coolant and chipsThree measuring points give the right bore size when the operator’s hand would otherwise decide the resultVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The scratch is visible to the eye but not in the report: how to measure directly on the microscope imageWhy a two-point measurement of a bore often shows the wrong diameter, and how a three-point micrometer solves itThree seconds instead of half a minute: how core temperature checks become a routine that actually gets doneA Hundred Bearing Seats per Shift: Read the Deviation Directly Instead of Calculating the DiameterThe hole measures correctly at the mouth but is tapered further in: how to find the fault without cutting up the partOne Second Is Enough to Tell Whether the Core Temperature PassesThree contact points give a bore measurement that doesn’t depend on who is holding the instrumentWhen the measurement has to be taken from an image: how automatic magnification reading makes microscope measurement traceableThe vernier caliper that keeps reading correctly when the scale is covered in coolant and chipsThree measuring points give the right bore size when the operator’s hand would otherwise decide the result

The Screw Is Always 25 Millimeters — It’s the Frame That Grows

Published August 27, 2026 at 18:17

A micrometer set for 0-300 mm consists of twelve instruments. The question most people have asked themselves at some point, without getting an answer, is why — why not a single micrometer that covers the whole range, the way a caliper does?

The answer lies in where the accuracy comes from. A micrometer measures by counting how far a precision screw has traveled. And an error in the screw’s pitch is repeated with every turn — the longer the screw, the more the error has time to add up.

Set of outside micrometers 0-300 mm in storage case

What it is

A set of outside micrometers for 0-300 mm.

  • Graduation 0.01 mm
  • Friction-coupled ratchet stop for consistent measuring force
  • Hardened measuring faces
  • Supplied in a sturdy storage case

Why 25 millimeters

The industry has solved the problem by locking the screw and letting the frame grow. Every micrometer in the set has the same screw with the same 25 mm travel; what differs between them is how deep the frame is. A gauge for 275-300 mm doesn’t have a screw twelve times longer — it has the same screw in a much larger frame.

This also explains the pricing. On a large micrometer, the cost lies in the frame: it must be rigid, dimensionally stable, and manufactured so that the distance between the anvil and the spindle end is precisely known. The mechanism is essentially the same as in the smallest instrument.

And it explains why zero is positioned differently. A 0-25 can be zeroed by closing it against itself. A 75-100 cannot — its zero point lies at 75 mm, somewhere in the air between the measuring faces, and must therefore be set against a known gauge of exactly that length. The larger the instrument, the more the measurement depends on the setting standard it is calibrated against.

The ratchet stop matters more in a set than in a single instrument

A set is used across a boundary. A part measuring 99 mm is measured with one instrument, one at 101 mm with the next — and the two readings need to be comparable, otherwise a jump appears in the data right where you switch frames.

If the contact force differs between the instruments, that jump becomes real: measuring force compresses both the workpiece and the frame slightly, and the difference shows up as a systematic step in the measurement series. The fact that every instrument in the set has the same friction-coupled ratchet stop is therefore not a convenience detail but the precondition for the set behaving as one measuring system.

Why large micrometers have looser accuracy requirements

A deep frame arch is both a longer heat path and a longer lever arm. Hand warmth travels into the material and makes the frame a few micrometers larger; gripping a large frame bends it imperceptibly but measurably. None of this is noticeable on a 0-25.

That’s why the specification for a large micrometer is always a little coarser than for a small one — the same pattern that applies to all long measuring instruments, where the error is expressed as a fixed part plus a part that grows with length. Knowing this means you don’t expect the same certainty at the upper end of a set as at the lower end.

Three typical use cases

  • Workshop with mixed production: a set covers everything instead of missing the exact size you need.
  • Incoming inspection: measuring parts across the full size range against drawings.
  • Toolmaking: work where dimensions vary from part to part.

Why it pays off

Buying the sizes one by one sounds cheaper, and rarely turns out that way. What you end up doing in practice is buying the two or three sizes you need right now — and then measuring with a caliper for every other size, because the instrument isn’t in the box when you need it.

A complete set removes that compromise and, in addition, turns the entire size range into one coherent measuring system: same screw, same measuring force, same reading. It’s rarely the individual instrument that determines the quality of a measurement series — it’s that every measurement in the series was made the same way.

Read more about the 0-300 mm micrometer set →

More news

All news