Hoppa till innehåll
Free shipping over 3000 kr excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%How to see the solder joint and the scratch without holding a magnifier over the circuit boardThe cold room was too warm last night, but nobody can show for how longWhy Two Operators Get Different Readings in the Same Bore, and How to Eliminate the DifferenceThe scratch is visible to the eye but not in the report: how to measure directly on the microscope imageWhy a two-point measurement of a bore often shows the wrong diameter, and how a three-point micrometer solves itThree seconds instead of half a minute: how core temperature checks become a routine that actually gets doneA Hundred Bearing Seats per Shift: Read the Deviation Directly Instead of Calculating the DiameterThe hole measures correctly at the mouth but is tapered further in: how to find the fault without cutting up the partOne Second Is Enough to Tell Whether the Core Temperature PassesThree contact points give a bore measurement that doesn’t depend on who is holding the instrumentVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%How to see the solder joint and the scratch without holding a magnifier over the circuit boardThe cold room was too warm last night, but nobody can show for how longWhy Two Operators Get Different Readings in the Same Bore, and How to Eliminate the DifferenceThe scratch is visible to the eye but not in the report: how to measure directly on the microscope imageWhy a two-point measurement of a bore often shows the wrong diameter, and how a three-point micrometer solves itThree seconds instead of half a minute: how core temperature checks become a routine that actually gets doneA Hundred Bearing Seats per Shift: Read the Deviation Directly Instead of Calculating the DiameterThe hole measures correctly at the mouth but is tapered further in: how to find the fault without cutting up the partOne Second Is Enough to Tell Whether the Core Temperature PassesThree contact points give a bore measurement that doesn’t depend on who is holding the instrument

One Second Is Enough to Tell Whether the Core Temperature Passes

Published 12 November 2026 at 02:08

You insert the probe into a pot, a cut of meat or an incoming delivery, and wait. The numbers on the display keep moving, and meanwhile the sample cools down, the door stays open or the queue grows. When the value finally stabilizes, it is unclear whether you measured the product or the surroundings. This is a common situation in kitchens and production lines, and it makes self-inspection both slow and uncertain.

ETI Thermapen® ONE Orange. Fast (1s) response time. Fold-out needle probe. Rotating display for easy reading. IP67. Backlit display. Calibration certificate

What the Thermapen ONE Is

The Thermapen ONE is a digital insertion thermometer with a fold-out needle probe. It reads the temperature in about one second and has an accuracy of ±0.3 °C between -19.9 and 119.9 °C. The measuring range is -49.9 to 299.9 °C with a resolution of 0.1 °C. The display rotates automatically so the value can be read however you hold the instrument, and it is backlit. The enclosure is rated IP67, so it withstands the kitchen sink and rinsing. The thermometer is powered by one AAA battery and goes into sleep mode when it is not moved. Every unit is delivered with a traceable calibration certificate, and the instrument complies with EN 13485.

What Problems It Solves

The most important difference compared with a slower thermometer is that you measure before the value has time to change. This applies especially to thin or small products, where the temperature changes within a few seconds. The rotating display and sleep mode also reduce the small annoyances that otherwise lead to checks being skipped. The calibration certificate means the measurement can be documented during an audit.

How It Is Used in Practice

Commercial kitchens and restaurants. The core temperature of fried and cooked food is checked at serving, as is the temperature during hot holding and cooling. With a one-second response time, the chef can measure several portions without having to stand still at each one.

Receiving inspection in food handling. At goods receipt, the probe is inserted into chilled and frozen packages to verify that the cold chain has held. The result is recorded immediately, before the delivery is accepted or returned.

Bakery and confectionery. Sugar, chocolate and batter have narrow temperature windows where a few degrees decide the outcome. Here, fast readings and 0.1 °C resolution are more valuable than a wide measuring range.

Why It Pays for Itself

The cost is seldom in the thermometer itself, but in what happens when the measurement is uncertain: discarded batches, rework, unnecessary overcooking and the time spent at each control point. A thermometer that gives a reliable value right away shortens each check and reduces the need to measure again. The five-year warranty and the traceable certificate also mean the instrument holds up over time and withstands scrutiny in a HACCP-based self-inspection program.

If you need a thermometer you can rely on in daily control, you can read more about the Thermapen ONE with us.

Read more

More news

All news