Hoppa till innehåll
Free shipping over 3000 kr excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Why Two Operators Get Different Readings in the Same Bore, and How to Eliminate the DifferenceThe scratch is visible to the eye but not in the report: how to measure directly on the microscope imageWhy a two-point measurement of a bore often shows the wrong diameter, and how a three-point micrometer solves itThree seconds instead of half a minute: how core temperature checks become a routine that actually gets doneA Hundred Bearing Seats per Shift: Read the Deviation Directly Instead of Calculating the DiameterThe hole measures correctly at the mouth but is tapered further in: how to find the fault without cutting up the partOne Second Is Enough to Tell Whether the Core Temperature PassesThree contact points give a bore measurement that doesn’t depend on who is holding the instrumentWhen the measurement has to be taken from an image: how automatic magnification reading makes microscope measurement traceableThe vernier caliper that keeps reading correctly when the scale is covered in coolant and chipsVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Why Two Operators Get Different Readings in the Same Bore, and How to Eliminate the DifferenceThe scratch is visible to the eye but not in the report: how to measure directly on the microscope imageWhy a two-point measurement of a bore often shows the wrong diameter, and how a three-point micrometer solves itThree seconds instead of half a minute: how core temperature checks become a routine that actually gets doneA Hundred Bearing Seats per Shift: Read the Deviation Directly Instead of Calculating the DiameterThe hole measures correctly at the mouth but is tapered further in: how to find the fault without cutting up the partOne Second Is Enough to Tell Whether the Core Temperature PassesThree contact points give a bore measurement that doesn’t depend on who is holding the instrumentWhen the measurement has to be taken from an image: how automatic magnification reading makes microscope measurement traceableThe vernier caliper that keeps reading correctly when the scale is covered in coolant and chips

Why Two Operators Get Different Readings in the Same Bore, and How to Eliminate the Difference

Published 18 November 2026 at 18:59

A bore of 18 mm must hold an H7 tolerance. The operator on the day shift measures 18.012, and a colleague on the evening shift measures 18.006 with the same instrument in the same bore. Nobody has been careless, but a two-point instrument in a small bore is sensitive to tilt and to where on the diameter the contact points land. It is one of the most common causes of disputes between production and quality.

Digital invändig trepunktsmikrometer av Holtest-typ, mätområde Ø16–20 mm

What a three-point micrometer is

This digital Holtest-type three-point internal micrometer has three carbide measuring surfaces positioned 120° apart. When you insert the measuring head into the bore, the instrument centers itself, and you read the diameter directly. The measuring range is Ø16–20 mm, the digital resolution is 0.001 mm, and the accuracy is approximately ±0.004 mm. This version is intended for blind holes, meaning holes where you need to measure close to the bottom. The instrument has an IP54 protection rating, can be switched between mm and inches, runs on a V357 battery, and is delivered in an aluminum case together with the manufacturer’s measurement report.

What problems it solves

The centering takes place in the instrument and not in the hand. This reduces the differences between users and makes the measured value more repeatable. Because you can measure at several depths in the same bore, you can also see whether the bore is tapered, something a single measurement can easily miss. Digital readout with 0.001 mm resolution also removes the interpretation of the scale and means the value can be read quickly at the machine.

When and how it is used

The instrument is zeroed on a setting ring of known diameter, preferably close to the nominal size. You then insert the measuring head, let the three surfaces make contact, and take the reading. Repeat the measurement at two or three depths, and preferably rotate the instrument a quarter turn between readings. The setting ring should be checked at regular intervals, since it determines how reliable the entire measurement chain is.

Three typical use cases

Machine shop industry: After reaming or fine turning a bearing seat or a guide bushing, the operator checks the bore directly at the machine. The correction can be made before the next part, not after an entire batch has gone to the quality department.

Hydraulics and pneumatics: Small valve bodies, piston bores, and cylinder liners have tight tolerances where the clearance determines whether the component leaks or runs stiffly. Here it is valuable to be able to see taper along the entire bore.

Maintenance and repair: When checking bushings and guide bores for wear, you compare the measured diameter against the drawing value and decide whether the part should be replaced or can be reused. With an instrument that gives the same value regardless of who measures, the decision is easier to justify.

Why it pays off

The cost of an uncertain bore measurement is seldom visible in a single measurement. It shows up in the scrapping of parts that were actually acceptable, in acceptable parts that then do not fit during assembly, and in the time spent comparing measurement results between shifts. An instrument that reduces the spread between users saves time in all of these areas. The included measurement report also gives you a basis for traceability from day one.

If you need to measure small bores with better repeatability than a two-point instrument provides, this micrometer is a natural choice.

Read more

More news

All news