Hoppa till innehåll
Free shipping over 3000 kr excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%How to see the solder joint and the scratch without holding a magnifier over the circuit boardThe cold room was too warm last night, but nobody can show for how longWhy Two Operators Get Different Readings in the Same Bore, and How to Eliminate the DifferenceThe scratch is visible to the eye but not in the report: how to measure directly on the microscope imageWhy a two-point measurement of a bore often shows the wrong diameter, and how a three-point micrometer solves itThree seconds instead of half a minute: how core temperature checks become a routine that actually gets doneA Hundred Bearing Seats per Shift: Read the Deviation Directly Instead of Calculating the DiameterThe hole measures correctly at the mouth but is tapered further in: how to find the fault without cutting up the partOne Second Is Enough to Tell Whether the Core Temperature PassesThree contact points give a bore measurement that doesn’t depend on who is holding the instrumentVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%How to see the solder joint and the scratch without holding a magnifier over the circuit boardThe cold room was too warm last night, but nobody can show for how longWhy Two Operators Get Different Readings in the Same Bore, and How to Eliminate the DifferenceThe scratch is visible to the eye but not in the report: how to measure directly on the microscope imageWhy a two-point measurement of a bore often shows the wrong diameter, and how a three-point micrometer solves itThree seconds instead of half a minute: how core temperature checks become a routine that actually gets doneA Hundred Bearing Seats per Shift: Read the Deviation Directly Instead of Calculating the DiameterThe hole measures correctly at the mouth but is tapered further in: how to find the fault without cutting up the partOne Second Is Enough to Tell Whether the Core Temperature PassesThree contact points give a bore measurement that doesn’t depend on who is holding the instrument

Kontolk for Conical Fit — a Cone Can Have Exactly the Right Diameter and Still Sit Wrong, Because It’s the Contact Surface That Holds

Published August 21, 2026 at 10:47

A tapered fit doesn’t hold thanks to a measurement, but thanks to friction over a surface. The tool stays put in the spindle because the taper and the bore bear against each other along their entire length; it is that contact which transmits the torque and which ensures the tool ends up centered every time. That’s why the common question — ”what’s the diameter of the taper?” — is the wrong question. A taper with the correct diameter but the wrong angle only makes contact in a narrow ring instead of over the whole surface, and the result is runout, vibration, and a spindle that wears unevenly.

LMW konisk plugtolk i härdat stål med läpp enligt DIN 235 för kontroll av koniska hål

What it is

A taper plug gauge in hardened steel with a step, manufactured to DIN 235, for metric taper 100. The gauge is hardened and ground to tolerance grade and is supplied with calibration documentation verifying both the taper angle and the large/small diameter. The plug version checks tapered bores; the corresponding ring gauge to DIN 234 is used for tapered shafts. The same family of gauges covers the common taper formats, from Morse taper to short SK-type tapers.

The problem it solves

A taper is defined by two things at once: the angle and the diameter at a specific reference plane. An ordinary diameter measurement only gives you one of these, and it cannot tell a correct taper apart from one that is right at one point and wrong everywhere else. The gauge solves both at once, by being a physical copy of the correct geometry.

The step is the key to diameter control. When the gauge is inserted into the bore, it stops at a defined axial position — and how far in it goes reveals immediately whether the bore is too large or too small. The step provides an accepted zone: if the edge of the bore falls within the step, the taper is within tolerance, so you read a diameter measurement as a position rather than as a number.

Contact checking handles the angle. A thin layer of engineer’s blue is applied to the gauge, it is inserted, turned slightly, and withdrawn again. The blue transfer pattern in the bore shows exactly where contact actually occurs: an even pattern over the full length means the angles match. If the blue only appears at the front end, the bore’s angle is too open; if it only appears at the innermost end, it’s too tight. This is a measurement that reveals the distribution rather than just a single figure — and it’s precisely that distribution which determines whether the fit will hold.

Why this matters so much in practice: a worn or damaged spindle taper causes contact to concentrate in a narrow zone. The pressure per unit area rises, wear accelerates, the tool is no longer drawn in symmetrically, and runout increases — and because the fault develops slowly, it’s usually perceived as ”the tools have gotten worse” or the machine has started vibrating for no reason. A gauge turns this into a measurable, actionable observation.

Three typical use cases

  • Incoming inspection of spindles and sleeves: verifying the taper before the component is installed or put into service.
  • Machine tool maintenance: periodic inspection of the spindle taper — especially after a crash, or when runout and surface finish have deteriorated without other explanation.
  • Manufacturing of tapered parts: inspection during machining, while the part is still fixtured and can be adjusted.

Why it pays off

Consider what rides on the taper. A spindle taper that doesn’t seat properly affects every tool mounted in the machine and therefore every part produced — not as a single defect, but as a systematic degradation of surface finish, dimensional spread, and tool life. The cost is spread across everything and therefore rarely shows up as a single line item, which is exactly what makes it hard to detect and easy to live with for far too long.

The flip side is the repair. A taper caught while the fault is still small can often be saved by lapping; one that’s allowed to keep working out of true wears down both itself and every tool holder placed in it — and at that point it’s no longer the spindle alone that needs fixing. The gauge is therefore cheapest exactly when it’s used routinely, before anyone has a reason to suspect a problem.

Read more about the taper plug gauge to DIN 235 →

More news

All news