Hoppa till innehåll
Free shipping over 3000 kr excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The temperature check that is no longer written on paper an hour after the measurementThe dishwasher’s display temperature doesn’t tell you how hot the plate actually gotHow to see the solder joint and the scratch without holding a magnifier over the circuit boardThe cold room was too warm last night, but nobody can show for how longWhy Two Operators Get Different Readings in the Same Bore, and How to Eliminate the DifferenceThe scratch is visible to the eye but not in the report: how to measure directly on the microscope imageWhy a two-point measurement of a bore often shows the wrong diameter, and how a three-point micrometer solves itThree seconds instead of half a minute: how core temperature checks become a routine that actually gets doneA Hundred Bearing Seats per Shift: Read the Deviation Directly Instead of Calculating the DiameterThe hole measures correctly at the mouth but is tapered further in: how to find the fault without cutting up the partVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The temperature check that is no longer written on paper an hour after the measurementThe dishwasher’s display temperature doesn’t tell you how hot the plate actually gotHow to see the solder joint and the scratch without holding a magnifier over the circuit boardThe cold room was too warm last night, but nobody can show for how longWhy Two Operators Get Different Readings in the Same Bore, and How to Eliminate the DifferenceThe scratch is visible to the eye but not in the report: how to measure directly on the microscope imageWhy a two-point measurement of a bore often shows the wrong diameter, and how a three-point micrometer solves itThree seconds instead of half a minute: how core temperature checks become a routine that actually gets doneA Hundred Bearing Seats per Shift: Read the Deviation Directly Instead of Calculating the DiameterThe hole measures correctly at the mouth but is tapered further in: how to find the fault without cutting up the part

Brake Disc Micrometer with 60° Point — a regular micrometer measures the edge of the disc, not the worn groove

Published August 20, 2026 at 02:15

A brake disc doesn’t wear evenly. The pad works against a band in the middle of the disc and leaves an untouched edge both at the outer and inner rim — the edge you can feel with your fingernail as a distinct lip. That’s exactly where an ordinary micrometer with flat anvils lands. The measuring face of Ø6.5 mm rests on the unworn edges, and the figure you read off is the disc’s original thickness, not the thickness actually remaining where the brake bites. The difference can be several tenths of a millimeter — and the decisions made on that figure concern brakes.

Analog brake disc micrometer with 60-degree point anvil, measuring range 7.6–33 mm and 88 mm throat depth

What it is

A micrometer built for brake discs, with a measuring range of 7.6–33 mm, graduation of 0.01 mm, and accuracy of ±0.004 mm. Two details set it apart from an ordinary outside micrometer: the anvil has a 60° point, and the frame has a throat depth of 88 mm. The measuring face against the point is carbide, Ø6.5 mm. Supplied in a wooden case.

The problem it solves

The point is the whole point. It reaches down into the worn groove, past the unworn edge, and measures the material where the brake pad has actually been working. That’s the only thickness that matters: a disc below the manufacturer’s stated minimum must be replaced, no matter how thick it is at the outer edge.

The deep 88 mm gap solves the second problem. A brake disc isn’t just measured at the edge — it should be checked at several points around the circumference and at different radii, since wear is rarely distributed evenly. With a shallow micrometer you only reach a few centimeters in from the outer edge and miss the part of the friction band closer to the hub. With an 88 mm throat depth, you can reach the entire band.

Measuring at multiple points also reveals something a single measurement never does: thickness variation. If the disc is a different thickness at different points around the circumference — DTV, disc thickness variation — you get a pulsating brake pedal and shaking in the steering wheel under braking. That’s the same symptom often wrongly blamed on ”warped discs,” and the difference between the two diagnoses is exactly this: one shows up in a multi-point thickness measurement, the other in a runout measurement with a dial indicator.

Three typical use cases

  • Auto workshops and service: checking against the manufacturer’s minimum thickness at every brake job — a basis for replace-or-keep decisions that can be noted on the work order.
  • Vibration troubleshooting: measuring at 6–8 points around the disc to determine whether a pulsating pedal is due to thickness variation or something else in the brake system.
  • Heavy vehicles and fleet workshops: planned maintenance where discs are checked at every service and replaced when the measurement — not a guess — says so.

Why it pays off

The instrument costs less than a single set of discs. The most common cost is discs being replaced unnecessarily ”to be safe,” because no one can show how much material is left — with a measurement that takes under a minute, that becomes a fact instead of a precaution. The second most common is the opposite: a disc left in service because the measurement was taken on the unworn edge and looked fine. There, the cost isn’t measured in money.

Add to that the troubleshooting time. Being able to distinguish thickness variation from runout with a quick series of measurements saves hours of swap-and-hope — and that customer won’t be back with the same vibration a week later.

Read more about the analog brake disc micrometer 7.6–33 mm →

More news

All news